hot tub water cloudy and dirty

Whirlpool-Wasser-trüb-und-schmutzig EGO3 Filter

Can I have cloudy water in the hot tub with an Ego3 filter?

Hot tub water cloudy and dirty?

Basically absolutely not, because the Ego3 has been tested tens of thousands of times and always works 100% and filters 100%! With Ego3 hot tub filters, there is no cloudy hot tub water during operation!

However, there are three reasons that, out of ignorance, are seen as filter faults, which can lead to cloudy hot tub water:

  1. The pH value is too high or the alkalinity too low. The water becomes milky. Unfortunately, this is a discoloration of the water and not cloudiness caused by suspended particles. Therefore, neither the Ego3 filter nor the cartridge filter can filter this. Remedy: Adjust pH value/TA value. Then the milky appearance goes away by itself. It is a discoloration of the water. This cannot be filtered.
  2. The disinfection is insufficient and/or the biofilm load is too high. Pay closer attention to disinfection! In this case, the filter continuously filters, but new dirt also continuously forms. The water is greenish / brownish.
  3. The water was clear so far but becomes cloudy at the beginning of using the Ego3 filter. This is due to a positive side effect of the Ego3 filter - the pipe cleaning effect. The Ego3 hot tub filter has about 2-3 times the flow rate of the cartridge filter (when new, otherwise even more). Due to the poor flow of the cartridge filter and because it cannot filter anything below 40 microns, these finest suspended particles settle in the pipes. The Ego3 hot tub filter now ensures that this dirt is "rubbed" out of the pipes. As a result, the hot tub water becomes cloudy until all the dirt is finally out of the pipes. This can take hours, days, or in cases of very strong pipe contamination, even 3-4 weeks. New dirt constantly comes out of the pipes and is immediately filtered again. Turning pumps on and off, as well as operating the distribution valves and air valves, speeds up the cleaning because it causes rapid flow changes. But after that, your pipes are finally clean, as they should be.

We guarantee you that the Ego3 filter always filters 100%.

How do I test the pipe cleaning effect?

Simply reinstall the old filter briefly. The water will become clear again temporarily because the dirt no longer immediately comes out of the pipes. But it should not be like that. The dirt belongs out of the pipes! Once that is accomplished, you will also notice that you need less chemistry because a bacteria source has been reduced.

Summary "hot tub water cloudy" despite Ego3:

  1. with milky discoloration only adjust the pH/TA value
  2. with greenish or brownish discoloration disinfection is too little 
  3. just let it run at initial cloudiness. Our filter cleans your pipes. And that is a good thing!

As always, you can always contact us as EGo3 customers by writing or calling if you have further questions.

Hot tub water cloudy - what to do?

If the disinfection system is okay, the pH and TA values fit, and the filters work, a hot tub must have clear water! 

Hot tub water must never be cloudy!

Therefore, I will explain each point one by one here that can be checked and improved to ensure that everything works.

cloudy hot tub water due to heavy use

AGAINST CLOUDY HOT TUB WATER

pH value setting done correctly against milky cloudiness of hot tub water

The pH value in a hot tub should always be between 6.8-7.2, otherwise every disinfectant is severely limited in its function. Hot tub water becomes cloudy at pH values that deviate 0.5 from 7.0. The hot tub water becomes milky cloudy. From 1.0 deviation completely milky. Attention: Many pH meters measure incorrectly if the TA value is not right. This is the most common error in hot tub water care.

Disinfection against greenish, brownish cloudy hot tub water

Color with insufficient disinfection - green, brown cloudy

Chemical disinfectants for hot tubs:

Chlorine, bromine, active oxygen
It is important that ozone and chlorine/bromine should not be mixed permanently! Both chlorine/bromine and ozone form free atoms that seek a bond (preferably with carbon = bacteria, algae, etc.) and if both are used simultaneously, it can happen that chlorine binds with oxygen instead of the atoms attacking the "bad, living" substances in the water made of carbon.

Automatic hot tub disinfection:

  • UVC - UV system: Make sure that the glass tube through which the water is irradiated is not fogged or dirty. This would reduce the radiation and massively reduce the disinfection effect.
  • Ozone system: The probably simplest, most efficient and healthiest way to disinfect hot tub water if you consider a few simple things.
    • Disinfection times: Always set to 24h circulation and ozone runtime at the beginning. If the water is perfect or in case of rare hot tub use, the times can also be reduced.
    • Ozonator: Different ozonators have different ozone production quantities. Choose the right ozonator.
      • Check if the installation direction of the ozonator fits (this is important for hot tubs with ozonators with membrane pumps!) and if it also works (usually indicated green by a control lamp).
      • Check if the suction side of the ozonator fits. Often the suction holes are designed far too small or covered with fibers to reduce humidity, which quickly clog. Drill the suction hole to at least 3mm and remove the piece of fabric on the suction side.
    • Ozone admixture: This is done using Mazzei injectors that work with the Venturi vacuum system and are connected to the ozonator by a hose line with a non-return valve.
    • Mazzei injector: The choice of the right injector and the correct water flow rate at the injector are important here. This can be influenced as follows:
      • Prevent alternative backflow possibilities so that as much water as possible must pass the circulation pump past the injector. Often waterfalls or hot water return lines are also connected to this circuit. Turn off waterfall when not in use! Turn off hot water return nozzle as far as possible if possible (this is often done by means of a hemisphere located at the tip, which is turned against the flow)!
      • Ensure flow in the ozone line: some hot tubs have mixing chambers installed that become dirty or coated with biofilm over time. Remove these mixing chambers. Ozone acts for 20 seconds. That means whether with or without mixing chamber, the return flow should last at least 20 seconds. This is easy to test by blocking the ozone intake and measuring how long it takes until ozone bubbles appear in the pool again after releasing the intake.
      • Check that the non-return valve in the Mazzei injector is not clogged or glued shut by dirt and thus does not open sufficiently.
      • Connection line ozonator - injector: These two components are connected with a hose line with a non-return valve.
      • Check whether the hose line is fully permeable (not kinked, not laid with dirt or nitric acid compounds (which form a sticky film in the hose during ozone generation))
      • Check whether the non-return valve in the line is fully permeable. Remove, wash through and blow through.
      • To avoid mistakenly sucking in air instead of ozone at the pipeline connection points, you can also seal all connection points with insulating tape.

And the most important point against cloudy hot tub water:

perfect hot tub water not cloudy

the right hot tub filter against cloudy hot tub water due to unfiltered suspended solids

EGO3 filter (+++): They can hardly clog because they do not act like a filter net of paper filters (cartridge filters), but according to the vortex principle along free flow channels. They filter out everything down to 1 micrometer and in enormous quantities, as the entire 3-dimensional space of the filter balls is available as filter space. In addition, these filter balls are much easier to clean and you can see if they are clean.

7_Vorteile_hot tub filter.JPG__PID:d6c7b147-af22-4393-a3e9-a75a65e8e5a8

Paper filter (-): When these filters become clogged, the flow rate naturally decreases and the suction at the injector also decreases, thus reducing the ozone feed. Filters are difficult to clean because sticky substances cannot be removed mechanically, only chemically. It is better to replace filters more often than too rarely. Filter effectiveness is limited by the fiber mesh size. The absorption capacity is limited by the relatively small filter surface. It is almost impossible to visually determine whether the filter has really been cleaned. Just because the filter is lighter again does not mean that the pores of the filter fabric are free again.


Back to the blog